Drying Systems - UMR Series
The UMR Series Mini Regenerative Desiccant Dryer offers a total cleaning
solution for many applications.
Standard Specifications:
-
Maximum Pressure: 225 PSIG (16 BAR)
-
Minimum Pressure: 29 PSIG (2 BAR)
-
Maximum Temperature: 158 F
-
Voltage: 115/1/60, 208-230/1/60, 220-240/1/50
-
Power Consumption: 12 Watt Max
-
Pre-filter Rating: 0.3 Micron (Coalescer)
-
Afterfilter Rating: 3.0 Micron (Particulate)
-
Cycle Time: 4 Minutes
-
Purge Loss: 12%
-
Air Outlet Conditions: Dry air down to -40 F Dew Point
-
Power Cord: Standard 8 ft
Features:
-
Microprocessor based controller for accurate and trouble free operation. >
-
Optional sub-micron prefilter for protection to the dryer and particulate
afterfilter captures desiccant dust keeping it from downstream components.
-
Shuttle valves for low pressure drop.
-
All Aluminum Drying Towers resist oxidation & scale formation.
-
1 year warranty with filtration package
|
 |
Drying Systems - UDL Series
Free water, water aerosols, and water vapor raise havoc on a
compressed air system. The Ultra Air Products UDL Series Drip Leg in
combination with coalescing filtration delivers an excellent but economical
package for ridding a system of this damaging water. Designed with an oversized
expansion chamber, the UDL Series offers one of the best water removal
efficiencies for drip legs on the market today. With its standard inlet and
drain ball valves, the UDL Series offers a terrific solution for any point of
use application where a system shutdown may be necessary.
Features:
-
Standard inlet and drain ball valves.
-
Primed and painted exterior
-
Expansion chamber is 3 x's the port size for tremendous water removal
efficiency.
-
1/4 NPT or BSPP to 2 NPT or BSPP thread size.
-
Full port ball valves.
-
Flexible part numbering system allows for multiple configurations to best fit
the application
|
 |
Drying Systems - 201 Series
The Ultra Air 201 Series Refrigerated Dryer provides just that: a
competitively priced dryer with consistent pressure dew points (33°F - 39°F),
delivered quickly and backed by a five-year warranty.
Every dryer is designed with energy savings in mind. All components are
properly sized to assure that no energy is wasted. Ample inside cabinet space
and easy access components make for simple future maintenance and adjustments.
Since only top quality components are utilized, the 201 Series will give the
customer years of uninterrupted service.
Standard Specifications:
-
Maximum Pressure: 225 PSIG (16 BAR)
-
Minimum Pressure: 29 PSIG (2 BAR)
-
Maximum Temperature: 158 F
-
Voltage: 115/1/60, 208-230/1/60, 220-240/1/50
-
Power Consumption: 12 Watt Max
-
Pre-filter Rating: 0.3 Micron (Coalescer)
-
Afterfilter Rating: 3.0 Micron (Particulate)
-
Cycle Time: 4 Minutes
-
Purge Loss: 12%
-
Air Outlet Conditions: Dry air down to -40 F Dew Point
-
Power Cord: Standard 8 ft
Features:
-
Standard suction and discharge gauges on units 125-2000 for easy detection of
pressures.
-
Thermostatic Expansion Valve - designed to maintain the proper evaporator
temperature.
-
Fan has sealed bearings, keeping it maintenance free for many years to come.
-
Hot Gas Bypass Valve designed to allow only gas no liquid - to inlet of
refrigerant compressor.
-
Standard liquid line filter dryer assures a clean, dry refrigerant system.
-
Powder coat paint finish
-
Heat Exchanger provides a 5 PSI or less pressure drop across the whole dryer,
even with the standard inlet filter. Specially designed for the compressor
dryer industry.
|
 |
Drying Systems - 301 Series
Today's ultra competitive business climate makes every dollar crucial in
order to stay competitive. The Ultra Air 301 Series Thermal Mass Cycling Dryer
offers energy savings that benefits that all-important bottom line. As its name
implies, it cycles the refrigerant compressor on and off only in times of need.
With standard, non-cycling refrigerated dryers the compressor remains on
whether there is a high or low load.
Features:
-
Standard suction and discharge gauges on all units for easy detection of
pressures. Standard electronic control panel for all models.
-
The compact, high efficiency counter-flowing evaporator minimizes the
compressor size allowing for maximum energy savings.
-
Fan has sealed bearings, keeping it maintenance free for many years to come.
-
The glycol tank uses welded fittings, assuring zero leakage.
-
Standard liquid line filter dryer assures a clean, dry refrigerant system.
-
Powder coat paint finish.
-
Circulation pump - the wet rotor design allows it to be maintenance-free and
minimize the energy consumed.
-
Zero Loss Drain - Does not allow expensive compressed air to pass
-
Heat Exchanger
-
Standard Delta Series™ 1 micron inlet filter removes oil and particulate,
keeping the heat exchanger efficient for many, many years.
|
 |
Drying Systems - UA Series
UA Series refrigerated air dryers use refrigerant to lower the temperature of
compressed air, therefore lowering its dew point. As the air temperature and
dew point drop, the moisture condenses into a liquid and is separated from your
compressed air and drained away. The end result is cool, clean, dry compressed
air ready to work for you and not damage your pneumatic equipment.
|
 |
Drying Systems - UDR Series
The UDR Series High Temperature Refrigerated Air Dryer provides clean, dry,
compressed air for auto body repair shops, auto service centers, dental
offices, and small manufacturers without the need for an aftercooler or
separator. The hot contaminated air first enters the standard coalescing filter
capturing damaging dirt, water and compressor oils. The air then enters the
dryer where it is cooled by R134a or R22 refrigerant (R134a and R22 are
environmentally acceptable and contains no ozone depleting CFC's). As the air
is cooled, the remaining water vapor is condensed into a liquid form. The
liquid is then separated from the air stream and drained away providing the
ideal air necessary to protect downstream components.
Features:
-
All copper constructed tube in tube heat exchanger to cool your compressed air
stream.
-
2 year warranty, 5 year heat exchanger warranty
-
Top quality refrigeration components
-
Electronic automatic condensation drain with push to test button on prefilter
and separator.
-
0.3 micron inlet coalescer oil removing filter.
-
Ambient air filter (standard).
-
R134a refrigerant for single phase units and R22 for 3 phase
units.(Environmentally acceptable - no CFC's)
-
Refrigerant analyzer gauge.
-
No aftercooler or separator required.
-
Made in the USA
|
 |
Drying Systems - LFT/LFE/LFA Series
Ultra Air Heatless Regenerative Dryers delivers a -40 F PDP, a dewpoint lower
than that required by the Instrument Society of America. In colder climates,
weather can negatively affect productivity by literally freezing and completely
blocking outdoor air lines. Instrument air requires a quality of air that only
a Regenerative type dryer can deliver. Therefore, whenever lower dewpoints are
required for outdoor piping, instrument air, process air or gas drying, the
Ultra Air Regenerative Dryings are the perfect solution.
Features:
-
Generous quantities of activated alumina desiccant
-
Centrally mounted pressure gauge and relief valves on each tower
-
ASME inspected and stamped and CRN registered pressure vessels (100 CFM and
above)
-
Purge air mufflers to reduce exhaust noise
-
115-160, NEMA 4x electrical
-
Repressurization of regenerating tower before it goes on drying cycle to
prevent desiccant dusting.
-
-40º F pressure dewpoint (lower dewpoint available)
-
Control air filter
-
Low pressure drops (3PSID maximum)
-
Fail safe mode
-
Dryer sequence lights
-
Reliable and proven inlet air control valves and purge valves assure years of
reliable shifting of towers and proper dryer operation (Lifetime Warranty) LF
Series 25-620 CFM.
-
1 year warranty
-
NEMA 4x
|
 |
| Questions, Comments: |
|
|
|
